Benchmarking: Bond/Barratt - Selbaie

Benchmarking: Bond/Barratt Specific Energy Consumption - Selbaie

Duval, L. and Wood, K., Testing, Design and Operation of SAG Circuit at Les Mines Selbaie, Proceedings of the SAG 1989 Conference, Vancouver, Canada, September 1989.

Wood, K. and Duval, L., Mill Expansion at Les Mines Selbaie, Proceedings of the 25th Anniversary Issue of the Canadian Mineral Processors, Ottawa, Canada (Paper № 8), January 1987.

Model Criteria

Two surveys was conducted in Nov 1988 and Dec 1988 and reported the following:

• Ore laboratory Bond rod mill work index: 16.5 metric
• Ore laboratory Bond ball mill work index, 104 µm closing mesh: 12.2 metric
• Ore laboratory Bond ball mill work index, 37 µm closing mesh: 13.2 metric
• MacPherson Autogenous work index (gross) of 20.1 metric (to 332 µm)
• MacPherson Autogenous work index (corrected) of 15.8 metric (to 332 µm)
• MacPherson ball mill operating work index of 13.8 metric (to 48 µm)
• MacPherson AB circuit operating work index of 16.1 metric (to 48 µm)
• Laboratory results were similar to the "ABCD" sample used as the plant design basis.
• Circuit FAG mill feed F₈₀ 117 mm
• Circuit transfer size T₈₀ 325 µm
• Circuit cyclone overflow P₈₀ 44 µm
• Circuit SAG operating work index of 20.0 metric (to 325 µm, measured at DCS)
• Circuit ball mill operating work index of 13.8 metric (to 45 µm, measured at DCS)
• Circuit total operating work index of 16.0 metric (117 mm to 45 µm, measured at DCS)
• Target throughput: 5000 t/d at 90% availability (231 t/h)
• Actual throughput: 5444 t/d at 93.5% availability (243 t/h)

The motors are described as:

• SAG mill is gear-driven with a DC variable speed motor having electrical efficiency of 0.925.
• SAG mill maximum speed (for "design" ore hardness) is 74% of critical speed.
• Ball mill is gear-driven with a fixed-speed synchronous motor (assume 0.96 electrical efficiency)

Additional data:

• SAG mill dimensions are given as 27 ft diameter by 11 ft long (not clear if this length is f/f or EGL)
  • Checking the Metso installation list, a 27 ft by 12 ft f/f long SAG mill was delivered to Quebec in 1985.
  • Duval & Wood (1989) say the discharge chamber is smaller than normal, so model a 10.5 ft EGL mill.
• Liner drawings show SAG mill hi/lo pattern with roughly 6 inch effective thickness.
• Ball mill dimensions are given in Wood & Duval (1987) as 16.5 ft diameter by 25.5 ft (?? f/f or EGL ??)
  • Checking the Metso installation list, a 16.5 ft by 25.5 ft f/f long ball mill was delivered to Quebec in 1985.
• SAG mill is normally operated at 8% v/v ball charge.

Additional model parameters

No crushing work index is provided, but we can make an assumption it is similar to the MacPherson Autogenous Work Index measured at Hazen.

• use Wi_C = 15.8 metric for modelling

The ball mill work index P80 values are not provided (only the closing mesh sizes) so a detailed ball mill Wi calibration to P80 cannot be performed. The target 44 µm will be somewhere between the expected test P80s of 37 µm and 105 µm closing meshes. Given the difference in work index is low (1.0 metric units), just model the arithmetic average of the two Wi_BM tests.

• use Wi_BM = 12.7 metric for modelling

No power draw numbers or mill filling values are given for the SAG or ball mill; only specific energy and work index values are provided. Assume for modelling:

• SAG mill filling is 25% v/v (gives about 85% of total power draw, sounds reasonable)
• ball mill filling is 32% v/v (gives about 95% of total power draw, sounds reasonable)

	SAG WiO, metric	Ball mill WiO, metric	Total WiO, metric	F80	T80	P80	Esag	Ebm	Etotal, kWh/t
Operating work index at DCS	20.0	13.8	16.0	117000	325	45	10.51	12.92	23.43
Electrical efficiency	0.925	0.960	0.946
Mechanical efficiency	0.985	0.985	0.985
Operating work index at shell	18.22	13.05	14.91	117000	325	45	9.58	12.21	21.79

Circuit Simulation

Screenshot of the Santa Rita circuit simulation

Combining the Bond/Barratt specific energy model, the Austin SAG model and the Nordberg wet overflow ball mill model results in the following throughput predictions using the work index values above:

	SAG	BM	total
Predicted specific energy consumption, kWh/t	11.99	12.37	24.37
Predicted operating work index, metric	20.32	14.20	16.67
Measured operating work index, metric
Difference, metric Wi units
Difference, %	%	%	%